- Bộ lập trình PLC, cáp lập trình
- Màn hình HMI
- Cảm biến, phụ kiện
- Biến tần, khởi động mềm
- Máy cắt, Aptomat, khởi động từ
- Thiết bị đo lường, bảo vệ
- Thiết bị công nghiệp, tự động hóa
- Thủy lực, khí nén, van công nghiệp
- Motor, Servo motor, Servo Amplifier
- Thyristor, Module, SCR, SSR, Diode
- Phụ kiện tủ điện và vỏ tủ điện
- Cáp điện, ống bảo vệ cáp
- Thiết bị điện trung thế, truyền tải
- Thiết bị chống sét, kim thu sét
- Dụng cụ cầm tay, dụng cụ tool
- ATS, UPS, tụ bù, cuộn kháng
-
Thiết bị ngành xi măng, thép, nhiệt điện
-
Thiết bị thanh lí-hàng tháo máy
Van điện từ, van nước, ZBSF-16P stainless steel high temperature steam solenoid valve DN15 20 25 32 40 50 65 80 100
Tình trạng sản phẩm:
First, ZBSF full stainless steel solenoid valve structure principle:
The valve is a direct-closing normally-closed solenoid valve in a step-by-step operation. After the coil is energized, the armature first drives the small valve to open, and the large valve opens under the effect of the formed medium pressure difference and electromagnetic force. The coil is de-energized, the armature component is reset, and the size valve is Use the pressure surface of the medium to close tightly.
Normally open solenoid valve, after the coil is energized, the armature moves down under the action of magnetic force, pushing the sub-valve valve plug down, until the sub-valve is pressed tightly, the auxiliary valve is closed, because the upper and lower pressure difference of the main valve cup tends to be equal, the main The valve cup is pressed tightly by magnetic force and self-weight, and the valve is closed. When the coil is de-energized, the magnetic force is zero, the armature and the auxiliary valve plug are lifted by the spring, the auxiliary valve is opened, the medium in the main valve cup flows away through the auxiliary valve, the pressure drops, and the main valve cup rises from the lower differential pressure The main valve opens and the valve opens.
Second, ZBSF full stainless steel solenoid valve anatomy:
Third, ZBSF full stainless steel solenoid valve specifications:
Fourth, ZBSF full stainless steel solenoid valve main uses:
ZBSF series all-stainless steel solenoid valve industrial process automation control system actuator. It can automatically open or close the electronic control signal to realize the on-off or flow regulation control of the fluid in the pipeline. This series of solenoid valves can be widely used. In the textile, printing, chemical, plastics, rubber, pharmaceutical, food, building materials, machinery, electrical appliances, surface treatment and other production and research departments as well as bathroom, canteen, air conditioning and other people's daily life facilities. ZBSF-Y series solenoid valve is mainly used Control of corrosive liquids, ultra-clean liquids and edible liquid media. ZBSF series solenoid valves are mainly used for gas medium control such as corrosive gas and super clean gas.
Five, ZBSF full stainless steel solenoid valve performance parameters:
| Working mediumPREFIX = O | Corrosive gas, short cold fluid, edible fluid ZBSF-1 :ZBSF-1Y for gas : ZBSF-2 for liquids : ZBSF-2Y for gases | ||||||
| Medium temperature( °C ) | ZBSF-1 :( 1Y ) ≤PREFIX = ST1 60 °C ; ZBSF-2 :( 2Y ) ≤200°C | ||||||
| Nominal pressure(Mpa) | 1.6 | ||||||
| Working pressure(Mpa) | 0 - 1.6 | ||||||
| voltage | AC220V, other specifications can be used for special order | ||||||
| Rated flow coefficient (KV) | By JB / T352-94 provisions | ||||||
| Leakage (m1/min) | By JB / T352-94.F provisions | ||||||
| Nominal diameter(mm) | 10 | 15 | 20 | 25 | 32 | 40 | 50 |
| Power consumption(AV | AC≤70VA | AC≤70VA | |||||
Six, ZBSF full stainless steel solenoid valve installation connection size:
| DN | L | H | D | D1 | D2 | b | f | Nd |
| 10 | 115 | 148 | Φ90 | Φ60 | Φ41 | 14 | 2 | 4-Φ14 |
| 15 | 115 | 148 | Φ95 | Φ65 | Φ46 | 14 | 2 | 4-Φ14 |
| 20 | 115 | 148 | Φ105 | Φ75 | Φ56 | 16 | 2 | 4-Φ14 |
| 25 | 125 | 148 | Φ115 | Φ85 | Φ65 | 16 | 3 | 4-Φ14 |
| 32 | 150 | 182 | Φ140 | Φ100 | Φ76 | 18 | 3 | 4-Φ18 |
| 40 | 165 | 182 | Φ150 | Φ110 | Φ84 | 18 | 3 | 4-Φ18 |
| 50 | 190 | 192 | Φ160 | Φ125 | Φ99 | 20 | 3 | 4-Φ18 |
| 65 | 290 | 265 | Φ185 | Φ145 | Φ118 | 20 | 3 | 8-Φ18 |
| 80 | 310 | 276 | Φ200 | Φ160 | Φ132 | 20 | 3 | 8-Φ18 |
| 100 | 350 | 373 | Φ220 | Φ185 | Φ156 | twenty two | 3 | 8-Φ18 |
| 125 | 400 | 416 | Φ250 | Φ210 | Φ184 | twenty two | 3 | 8-Φ18 |
| 150 | 480 | 440 | Φ285 | Φ240 | Φ211 | twenty four | 3 | 8-Φ22 |
Seven, ZBSF full stainless steel solenoid valve installation instructions:
1. When installing, the solenoid valve coil is upward and maintains the vertical position. The arrow or mark on the solenoid valve should be consistent with the flow direction of the pipeline, and should not be installed in places with splashing water or water leakage.
2. The working medium of the solenoid valve should be clean and free of particulate impurities. The dirt and filter on the surface of the solenoid valve internal parts should be cleaned regularly.
3. When the solenoid valve is faulty, in order to isolate the solenoid valve in time and ensure the normal operation of the system, it is better to install a bypass device (Figure 1). Note: The valve on the bypass must be closed normally. If the solenoid valve is mounted on the bracket, the diameter of the solenoid valve should be smaller than the diameter of the valve on the main pipe.Figure (2).
4. Before installing the solenoid valve, the pipe must be cleaned. It is recommended to install a filter in front of the valve and a steam pipe to install the trap.
5. Do not install the valve in the low recess of the pipeline to prevent the condensation of steam, impurities and the like from freezing in the valve.
6, ordinary type can not be used in explosive places.
7. In the case of insufficient rigidity of the pipeline, it is recommended to fix the front and rear pipes with brackets to prevent vibration when the solenoid valve is working.
8. Before installation, pay attention to see the product label, read the instruction manual carefully, and judge whether the product meets the conditions of use.
9. The pressure gauge should be installed on the pipeline before and after the solenoid valve to observe the pipeline pressure.
2. The working medium of the solenoid valve should be clean and free of particulate impurities. The dirt and filter on the surface of the solenoid valve internal parts should be cleaned regularly.
3. When the solenoid valve is faulty, in order to isolate the solenoid valve in time and ensure the normal operation of the system, it is better to install a bypass device (Figure 1). Note: The valve on the bypass must be closed normally. If the solenoid valve is mounted on the bracket, the diameter of the solenoid valve should be smaller than the diameter of the valve on the main pipe.Figure (2).
4. Before installing the solenoid valve, the pipe must be cleaned. It is recommended to install a filter in front of the valve and a steam pipe to install the trap.
5. Do not install the valve in the low recess of the pipeline to prevent the condensation of steam, impurities and the like from freezing in the valve.
6, ordinary type can not be used in explosive places.
7. In the case of insufficient rigidity of the pipeline, it is recommended to fix the front and rear pipes with brackets to prevent vibration when the solenoid valve is working.
8. Before installation, pay attention to see the product label, read the instruction manual carefully, and judge whether the product meets the conditions of use.
9. The pressure gauge should be installed on the pipeline before and after the solenoid valve to observe the pipeline pressure.
Eight, ZBSF all stainless steel solenoid valve use and maintenance:
1. It is recommended to use a designated person to take care of the use.
2. After the solenoid valve is installed, it must be tested by the medium for several times. After confirming the normal condition, it can be put into formal use.
3. The dirt inside and outside the large valve and the suction surface of the armature should be cleaned regularly. Be careful not to damage the sealing surface.
4. When the solenoid valve is not used for a long time, the manual valve before the valve should be closed. When re-enabling, the steam solenoid valve should remove the condensed water and make a trial operation several times. It can be put into use after the switch is normal.
5. When the solenoid valve is removed from the pipeline, the internal parts should be tested and compressed and stored with compressed air.
6. When the use time is long, if the seal between the piston and the valve seat is not good, the piston sealing surface can be re-polished and then grinded with the valve seat.
7. When working, pay attention to the pressure gauge before and after the valve, the working pressure should not exceed the rated pressure, and the working pressure difference must be within the rated pressure difference. When the working pressure exceeds the rated pressure or the working pressure difference exceeds the rated pressure difference, the solenoid valve should be stopped, and the front and rear manual valves should be closed to prevent the solenoid valve from exploding and leaking.
2. After the solenoid valve is installed, it must be tested by the medium for several times. After confirming the normal condition, it can be put into formal use.
3. The dirt inside and outside the large valve and the suction surface of the armature should be cleaned regularly. Be careful not to damage the sealing surface.
4. When the solenoid valve is not used for a long time, the manual valve before the valve should be closed. When re-enabling, the steam solenoid valve should remove the condensed water and make a trial operation several times. It can be put into use after the switch is normal.
5. When the solenoid valve is removed from the pipeline, the internal parts should be tested and compressed and stored with compressed air.
6. When the use time is long, if the seal between the piston and the valve seat is not good, the piston sealing surface can be re-polished and then grinded with the valve seat.
7. When working, pay attention to the pressure gauge before and after the valve, the working pressure should not exceed the rated pressure, and the working pressure difference must be within the rated pressure difference. When the working pressure exceeds the rated pressure or the working pressure difference exceeds the rated pressure difference, the solenoid valve should be stopped, and the front and rear manual valves should be closed to prevent the solenoid valve from exploding and leaking.
Nine, ZBSF full stainless steel solenoid valve ordering instructions:
(1) Please specify the following when ordering:
1. ZBSF stainless steel solenoid valve voltage (AC220V, DC24V);
1. ZBSF stainless steel solenoid valve voltage (AC220V, DC24V);
2.ZBSF stainless steel solenoid valve working pressure (0-1.6);
3.ZBSF stainless steel solenoid valve nominal diameter (15-300);
4.ZBSF stainless steel solenoid valve uses medium (water, corrosive fluid, super clean fluid, edible fluid);
5.ZBSF stainless steel solenoid valve connection (flange connection, wire connection);
6.ZBSF stainless steel solenoid valve medium temperature (0-200 ° C).
(2), the valve opening time is up to 12 hours / day or more, please use the normally open solenoid valve. When there is flammable and explosive material around the use environment, please use explosion-proof solenoid valve.
THÔNG TIN THANH TOÁN
| |||||||||
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
TÂN THÀNH CAM KẾT
- Sản phẩm, hàng hóa chính hãng.
- Giá cả cạnh tranh.
- Dịch vụ chăm sóc khách hàng tận tâm.
Thông Tin Công Ty
Chính sách và quy định
Đã thông báo
Hỗ trợ khách hàng
THÔNG TIN LIÊN HỆ:
-------------------------------
CÔNG TY TNHH THIẾT BỊ CÔNG NGHIỆP TTH
Trụ sở: số 124 ngõ 79 Yên Hoà-Cầu giấy-HN
Kinh doanh 1 : 0816.861.515
Kinh doanh 2 : 0836.861.515
Kinh doanh 3 : 0926.511.515
Kinh doanh 4 : 0916.861.515
Kinh doanh 5 : 0888.868.515
Kinh doanh 6 : 0917.971.515
Website: http://tanthanh-automation.com
Website: http://thietbitudongtanthanh.com
Website: http://diencongnghieptanthanh.com
Email: tthkinhdoanh@gmail.com
Email: tthkinhdoanh01@gmail.com
